Electronics I Lab, Assignment #1, Nicole Skinner

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253
Across
  1. 3. Write down the date and ______ for oscilloscope screenshots.
  2. 4. This button will open the waveform generator instrument in ADK.
  3. 5. If a person is suffering from electric shock, turn ______ electrical power source.
  4. 7. Prevent connecting the input connector to the ______ connector.
  5. 10. Plagiarized material will be graded as this number.
  6. 12. The text next to the cursor if you hover it above a tool button in Multisim.
  7. 14. Make sure your solder is ______ free .
  8. 15. The number of times you are graded for lab proficiency.
  9. 17. The group in the Multisim components tools bar that allows you to place resistors.
  10. 19. The view in ADK that allows you to access signal type, frequency and phase.
  11. 24. Submissions on blackboard shall not use this type of block.
  12. 27. MATLAB uses this variable to store the results of a calculation.
  13. 29. Read the lab ______ before the start of your lab .
  14. 31. The panel where you can build an output signal in ADK.
  15. 33. Your report's point size should be between 10 and ______ .
  16. 34. Recordings of classroom lectures is considered this type of property.
  17. 35. Analog and Oscilloscope screenshots need your ______ number included.
  18. 38. The number of isolated output channels the Keithley power supply offers.
  19. 39. Use this application when designing a graph for your report .
  20. 40. Use load ______ heavy enough so that they won't be overheated.
  21. 41. The number of points deducted per missing lab or lecture session.
  22. 42. This button on the power supply will set the voltage output.
  23. 43. In Analog Discovery 2's o-scope, this button will begin capturing data.
  24. 45. The number of times your notebook will be graded a semester.
  25. 46. In case of an emergency, call the university ______.
  26. 49. Lab reports are worth this percent of your grade.
  27. 50. Refrain from eating in the lab to avoid ingesting.
  28. 53. Use this application when designing a table for your report.
Down
  1. 1. Before powering an o-scope, ground it and ______ .
  2. 2. The % symbol in MATLAB will ______ your code.
  3. 6. The function generator has three generators in one and a ______ counter.
  4. 8. Include ______ of your completed breadboard and setup .
  5. 9. Observe all terminal ______ to prevent fire or shock hazards.
  6. 11. The panel used to explore data that you create or import files from in MATLAB.
  7. 13. Keep fingers behind the finger guards on the o-scope ______.
  8. 16. The oscilloscope allows you to store data externally through this device.
  9. 18. If the power supply doesn't turn on, the first step is to check ______ cord.
  10. 20. To place a pin array in Multisim, first select this tab.
  11. 21. The type of panel buttons on the o-scope to set up analog channels.
  12. 22. Don't forget to perform all ______ in your notebook beforehand .
  13. 23. From this tab, begin entering values for BJTs in Multisim.
  14. 25. The time by which items are due on blackboard .
  15. 26. What you absolutely cannot record your notebook with.
  16. 28. The tab in Multisim where errors from SPICE netlist checks appear.
  17. 30. This function creates 2D line plots in MATLAB.
  18. 31. This command in the power supply clears the event registers and error queues.
  19. 32. A list of commands that will be executed by MATLAB.
  20. 36. Number of prongs your power cords must need.
  21. 37. The application allows you to access Analog Discovery devices.
  22. 43. A grading tool that will be used when grading a lab report.
  23. 44. These buttons on the function generator are labeled as item number one.
  24. 47. This should be drawn through your mistake in your notebook.
  25. 48. Submit your pre-lab to ______ before your lab period.
  26. 51. Next to your mistake in your notebook this will be added.
  27. 52. Don't use this to extinguish an electrical fire .