Across
- 2. BXD Day 4: At least one embossed ___ ___ needs to be visible on each graft.
- 5. Wipe the sealer with 70% IPA before and ___ use.
- 8. BXD Day 4: ___ ___ is not acceptable in final grafts. Contact a supervisor or designee if it is detected.
- 11. Gen Day 2: Once tissue is placed on the drying board, cover the tissue with skin mesh and gently __ __ with a protowel.
- 12. If holding in Poly-poly double packaging exceeds ___ days, contact supervisor.
- 13. The purpose of Day 3 is to verify that the tissue is dehydrated, and to choose the appropriate ___ for the tissue.
- 14. The mission of Solvita is: ___ people to save and enhance lives.
- 15. If tissue does not populate on the Birth Tissue Priority Board, initiate MFG-722-JA-02 Dental Birth Tissue ___ ___ Process Job Aid.
- 16. Gen Day 4: Cut a greater than or equal to 2x5cm sample for ___ ___ testing from the membrane.
- 21. BXD Day 2: Start all 6, then tighten the middle thumb nuts down. After the thumb nuts are tight, work ___ to tighten the corner thumb nuts.
- 22. Gen Day 2: After water soaks, pat membrane with pro-towel. Membrane should be able to be lifted without ___.
- 26. Gen Day 4: When possible, use embossed ___ to help create straight and consistent cuts.
- 27. Day 2: Verify donor number on printed ___ labels match donor number listed on batch record.
- 28. BXD Day 4: If __ __ __ was not utilized for the cutting and measuring of grafts, the graft reviewer must verify each graft size with a ruler to ensure it is within tolerance.
- 30. If tissue is not scanned into the unit ___, a comment is required to be entered into DELTA.
- 32. BXD Day 2: Place chorion membrane basement membrane side ___ on top of the amnion to cover as much space as possible.
- 34. BXD Day 2: Place amnion on white board basement membrane ___ ___.
- 36. BXD Day 2: A two-person verification that the ___ cells were removed is required.
- 37. Day 4: Although grafts are packaged in fresh-frozen type packaging, membrane is dehydrated and should be labeled with a ___ tag.
Down
- 1. BXD Day 4: Do not use areas where tissue contain blood spots, lack of ___, tears.
- 3. Sterile tech must change ___ after draping heat sealer and prior to returning to sterile field.
- 4. SOPs can be found on ___ ___.
- 6. BXD Day 2: Label each container with the following: Donor ID, Water, Amnion or Chorion, ___/___, and Tech's initials.
- 7. The Director of Manufacturing is ___ ___.
- 9. A ___ ___ verification must be performed before receiving tissue.
- 10. BXD Day 4: Size tolerance is plus or minus __ __.
- 12. The BSC must run for approx. ___ minutes to purge the BSC of any particulates prior to use.
- 14. BXD: Amnion and chorion from donor are placed in refrigerator at different times. Ensure that chorion ___ the minimum time limit and that amnion times does not exceed maximum limit.
- 17. Gen Day 1: The lid for antibiotics must be secured prior to introduction of ___ in the BSC.
- 18. The manager of Birth Tissue is ___ ___.
- 19. BXD Day 2: Place amnion membrane on the drying fixture. Basement membrane side will be placed ___.
- 20. BXD Day 4: Donors which are ___ in color are unaccepable.
- 23. BXD Day 2: If decanting into a bowl, sterile technician should either ___ ___ out with pro-towels or receive new bowls to prevent residual 0.9% saline from being transferred to the tissue in future steps.
- 24. Never operate the BSC while the ___ alarm indicator is on.
- 25. If tissue is adequately dehydrated but packaging will not take place within ___ hours from start time of dehydration, tissue is to be placed into a poly-poly double packaging and scanned into quarantine holding.
- 26. The minimum PPE requirements for making LpH are ___ and gloves.
- 29. Gen Day 2: Remove __ __ by gently massaging them towards the closest edge of the tissue or by picking up part of the tissue to let air escape before placing it back on the Teflon block.
- 31. When making LpH, rinse interior of the pump sprayer with ___ ___.
- 33. BXD Day 4: Place ___ ___ on upper left corner of pouch.
- 35. Do not set ___ on shaker.