Across
- 1. _______ is the distance between parallel lines.
- 3. This line when made is called a ______ ‘around’ on the tubing that are made to go completely around the tubing is called? Or a type of sandwich that has a tortilla type bread that is folded around ingredients.
- 5. A transversal line can become a ________ leg when bending an offset.
- 8. The opposite of equal.
- 9. A general term to describe something that is less than 45 degrees.
- 11. This is where two lines come together and form an angle.
- 12. This is one of the measurements of pipe or tubing diameter. Something your parents asked you to play when you were making too much noise?
- 14. The distance from the center of a bend where the tube is straight is called ________.
- 16. _________ is the distance the tube advances from the setback location to where the tube becomes straight again.
- 20. Is a math term that represents when numbers are times one another.
- 21. The number of named parts of a tubing bended
- 22. This type of angle is any whose sum is 90 degrees.
- 24. This mathematical term is when you take numbers and combine the total of them.
- 25. Is a math term when calculating how many of an amount is in a total amount.
- 26. This offset starts at a bottom corner of an isometric box and has a travel piece that ends its offset at the opposite top corner of the isometric box.
- 30. The distance on a parallel line from where the travel leg starts to the offset location is called the run or __________.
- 31. You use this degree measurement number to line up bend mark on the faceplate and the roll support on short hand.
- 36. A tubing bender makes round bends that is based on one half of the circles_________.
- 37. In tube bending the mathematical difference between the lengths of two setbacks and the advance.
- 38. This angle is more than zero, but less than 90 degrees.
- 40. This type of drawings will help someone better visualize the bending needed.
- 41. A straight angle is also a straight line. It contains 180 degrees from point to point. It can be called the ____________.
- 43. The exact middle of a circle could be called this.
- 44. This direction is on the ‘isometric’ compass, though it is not North, South, East, or West.
- 47. Is what you do to tubing when measuring and marking out a tube to be bent. Or when you are calculating and designing how a piping arrangement will be completed from start to finish.
- 48. There are three sides to a triangle, if two sides have a known dimension the third side would be considered to be _________ dimension. Or some people say this about heaven or the start of a journey this ‘the great ________”
Down
- 2. This could be called the mathematical recipe to find a mathematical unknown.
- 4. This direction is on the ‘isometric’ compass, though it is not North, South, East, or West.
- 6. A general term to describe something that is greater than 45 degrees.
- 7. This mathematical term is when you take numbers and remove some of them from the other number and you have a new total.
- 10. This is the term used to describe the measurement from one end of a piece of tubing to the other end of the tubing.
- 13. A circle has 360 of this measurement.
- 14. This allowance (sometimes also called ‘Gain”) is the adjustment to the length. Or you do this when placing peanut butter on bread evenly.
- 15. This side of the triangle is against the 90-degree angle and the hypotenuse.
- 17. When laying out the _________ point it is the location where the measurement begins. It is also called the "Dumb End"
- 18. The Pythagoras the Greek philosopher theorem on sum of a right triangles is called __________ theory.
- 19. Is the name for the longest side of a triangle.
- 23. This shape has three sides.
- 27. Setback, Advance, and Gain is the method used in tube bending
- 28. What the tool name, that is used for the S.A.G. method.
- 29. This type of root is not grown but is used in math.
- 32. This angle has more than 90 degrees.
- 33. Is an angle whose vertex is located in the center of a circle.
- 34. This side of the triangle has the degree locator and corners of the hypotenuse and is called the run.
- 35. What tool can be used to help make sure your second bend is level or plumb?
- 39. A term that describes when you use a mathematical formula to achieve and answer.
- 42. If you have a angle of 20 degree, what is the rest of the degrees needed to be complementary angle?
- 45. What is used to help with bending to keep the tubing ‘square’ with a bending table and the bender? Or a name given to items used in movies that fill in details of a set.
- 46. Every _______ has two setbacks.