EECE.3110: Electronics I Lab

Edit Answers
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748
Across
  1. 3. [blank] must be completed and submitted to Blackboard prior to the scheduled lab session.
  2. 7. The university uses [blank] solder because it is safer.
  3. 8. This power supply maintains a [blank] voltage and current on channels one and two.
  4. 11. image 1
  5. 12. [blank] is the best color of ink to use for proper aging purposes.
  6. 13. The software to run the ADK is called [blank].
  7. 16. The ADK has a built-in [blank], function generator, power supply and digital I/O signals.
  8. 19. Lab [blank] evaluations are a verbal test to the knowledge preformed in lab and these tests occur twice a semester.
  9. 22. This power supply has a current [blank] that limits the amount of current that can be delivered to the load, ultimately protecting the circuit.
  10. 23. Bowden’s office hours are on [blank] from 10:30AM – 11:30AM or by appointment.
  11. 25. The [blank] function on the oscilloscope can be used to display a specific part of the signal needed.
  12. 27. The AFG1022 can produce [blank] different waveforms at the same time.
  13. 28. A [blank] is a component that protects a circuit against too much current.
  14. 29. An [blank] notebook is used to record laboratory findings and notes from completion of the lab session.
  15. 30. In MATLAB the file type is a [blank] file.
  16. 31. If you miss a [blank], expect a deduction on the final grade of the assignment or lab report daily.
  17. 32. To generate a waveform on a function generator, input the frequency in hertz or period in seconds and the [blank] in volts.
  18. 34. The default setting for placing components is snap to [blank] on Multisim.
  19. 35. Only black or [blank] pen can be used in a laboratory notebook.
  20. 37. By pressing the [blank] button on the oscilloscope, it will run a single cycle of the wave from a connected circuit.
  21. 39. In any blank or empty [blank] cross the area out with an ‘X’.
  22. 40. Multisim is a software for designing [blank] digitally.
  23. 46. The [blank] generator is used to produce a periodic wave signal.
  24. 47. To measure voltage with a voltmeter, put the DMM in [blank] with the desired component.
  25. 48. The [blank] terminal is to direct the positive charges to go to a safe place and to protect the circuit.
Down
  1. 1. The most relevant MATLAB help can be found on the [blank] website.
  2. 2. Function generators can create a [blank] waveform, which linearly varies the frequency at a constant amplitude.
  3. 4. image 4
  4. 5. In MATLAB, when using the plot function, at the end include this: ‘r-’. This creates a red [blank].
  5. 6. image 3
  6. 8. There are two to four [blank] on an average oscilloscope which are using to probe circuits.
  7. 9. A function generator can output sine waves, square waves, [blank] waves or also known as ramp waves, etc.
  8. 10. image 2
  9. 14. In MATLAB, the syntax is to include a [blank] to the end of every line.
  10. 15. To measure current with an ammeter, put the DMM in [blank] with the circuit.
  11. 17. image 5
  12. 18. Check [blank] to see your grades and to find all material for the semester.
  13. 20. If you right click on a line and select ‘Color Segment’, you can change the [blank] of the connection line.
  14. 21. The [blank] on a wave signal is the amount of cycles per second and can be expressed in the unit Hertz (Hz).
  15. 24. [blank] is required to Friday lectures and lab sessions.
  16. 26. No [blank] or drinking in the lab room; all food and drinks must be placed on the designated table before start of lab.
  17. 33. National [blank] owns Multisim and Ultiboard.
  18. 35. Bowden and Phillip’s Office are in [blank].
  19. 36. Multisim has a [blank] function which allows the circuit to perform the way it should in real time.
  20. 38. A power supply outputs [blank] current voltage.
  21. 41. [blank] lab reports are a blessing and don’t require to write a summary/abstract, introduction, the written portion in the measurements section, and the question section.
  22. 42. The bottom of the page requires a [blank] after completion of each page.
  23. 43. To learn the basic functions of MATLAB, take the course on the Mathworks website, [blank].
  24. 44. Oscilloscope [blank] are connected to the channels used to measure voltage in a circuit.
  25. 45. The ADK has a [blank] adapter to connect an oscilloscope probe.