Across
- 5. This section of the lab report is considered as the heart of note writing. It includes data that is gathered from taking all the measurements.
- 6. This component toolbar button selects the source components group in the browser.
- 9. These coverings are required for all students regardless of vaccination status in all indoor spaces.
- 12. All assignments are to be submitted here using Blackboard.
- 15. This analog acquisition mode calculated the average value for each record point over a user specified number of acquisitions.
- 16. (1+ 1-) and (2+ 2-) in the Analog Discovery 2 are used to capture and analyze analog signals.
- 19. This math software package is to be used to perform all the calculations and it can also be used to draw a graph.
- 21. The process of connecting the output signal back to the input of the same amplifier.
- 22. This analog acquisition mode retains the first sampled point from each acquisition interval.
- 23. When this feature is enabled, the displayed reading is the difference between the measured input signal and the stored null value.
- 26. This simulation toolbar button starts/resumes the simulation of the active circuit.
- 27. Device used to apply specified analog signals to circuits.
- 31. “ ./ “ is one of the operators used in MATLAB.
- 34. Call them in case of an emergency. From Lab Phone use x44911 and from Cell Phone use 9789344911.
- 35. This indicator indicates that the external triggering is enabled.
- 36. Arrays Multidimensional arrays in MATLAB whose elements are copies of other arrays.
- 37. When using devices such as the Analog Discovery and the Oscilloscope, screenshot/capture submissions must include this number along with the date and time it was taken.
- 41. Abbreviation for “Metal oxide field effect transistor”.
- 42. Practice of copying someone’s work or ideas.
- 43. is highly recommended that you back-up all lab data onto this device.
- 45. Indicating the page numbers after the end of each page.
- 48. This menu button is used to perform an automatic setup of oscilloscope settings.
- 49. This is one of the two acceptable formats for referencing in your lab report.
- 50. This button can be used to set the output load value to either 50 Ohms or High Z mode.
Down
- 1. Required as a proof of author’s work and can also be used to provide a proof of witness.
- 2. A type of circuit that is used to increase the voltage, current, or power of a signal.
- 3. A type of circuit that is used to compare two inputs.
- 4. This trigger option selects the internal trigger source.
- 7. This sign in waveforms shows that the device is armed and is waiting for a trigger event to occur.
- 8. Virtual instrument suite used for Analog Discovery 2.
- 10. The property of a capacitor to store an electrical charge.
- 11. This is a function that provides value of 3.14159265…
- 13. This graphs properties button specifies a label for the trace.
- 14. Enables/Disables the averaging digital filter.
- 17. This is a hands-on laboratory evaluation of your laboratory knowledge and skills.
- 18. These types of keys are grey. Pressing one of them causes the instrument to perform a specific operation. Config key is an example.
- 20. This sign indicates an injury hazard not immediately accessible as you read the marking.
- 24. This instrument toolbar button places the multimeter on the workspace.
- 25. This mathematical function calculates the ratio of measured reading to a specified target value in the form of percentage.
- 28. Last name of the author of “Writing the Laboratory Notebook”.
- 29. (V+ V-) in the Analog Discovery 2 are used to supply power to a circuit.
- 30. These types of keys are white. Pressing one of them causes the instrument to perform a specific function. DCV key is an example.
- 32. This button is used to select the shape of waveform among sine, square, ramp, or arb.
- 33. Number of stroke(s) needed to cross out the incorrect data in the notebook.
- 38. This display button is used to activate the system utility functions, such as selecting a language or setting the date/time.
- 39. The functions “ A ^ (1/2) and “ A. ^ (1/2)” are used to solve these types of math functions.
- 40. “ .^ “ is one of the operators used in MATLAB.
- 44. This section of the lab report is a mini version of the lab report. It contains an overview of the lab and the main conclusion(s) drawn from the lab.
- 46. This menu button is used to perform automated measurements on waveforms and to access the digital voltmeter and waveform histogram functions.
- 47. This button in Output options tab prints the circuit and faces of the instruments used in the circuit on a separate sheet.