Electronics II Lab - Daniel Abreu Fernandez

Edit Answers
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354
Across
  1. 2. These type of notebooks do not use spiral metal binding but rather pages that are sewn and glued.
  2. 5. Black pens of this type are the best for laboratory note taking.
  3. 6. A separate addon to the ADK that allows you to analyze characteristics of diodes and transistors.
  4. 8. This section of your notebook provides the page numbers to your experiment notes.
  5. 10. This parameter limits the highest frequency that an oscilloscope might sense from an in wave.
  6. 13. Use this software to simulate circuits prior to coming into lab.
  7. 18. This circuit component resists the change of current.
  8. 21. This button on your benchtop oscilloscope automatically sets up horizontal divisions to look at the signal being measured in clear detail.
  9. 22. Component that only allows electron flow
  10. 23. This component causes all DC currents to equal 0 in it's respective branch.
  11. 25. Press this button on the function generator in order to modify the period of your signal.
  12. 27. A compound found in ink that reacts with moisture and causes damage to paper cellulose atoms.
  13. 29. Bayonet Neill-Concelman
  14. 30. Analog-to-Digital converter
  15. 31. This capacitor implementation shorts any DC signal and allows AC signals to pass.
  16. 32. Universal asynchronous receiver-transmitter
  17. 33. The ratio between output voltage to input voltage in a amplifier circuit.
  18. 34. This amplifier setup has the input signal applied between the base and the emitter.
  19. 36. This capacitor implementation shorts any AC signal to ground to remove noise from DC signals.
  20. 37. You should never be ____ in the lab even if you are hungry. Come prepared!
  21. 40. Press this button on the function generator in order to modify signal amplitude.
  22. 41. Should be done prior to starting a new lab.
  23. 42. This parameter moves an AC signal up or down the y-axis.
  24. 43. Section of your lab report that includes all graphs, data, and tables.
  25. 44. Serial Peripheral Interface
  26. 48. Three terminal semiconductor device used to switch or amplify signals.
  27. 52. After your lab period is over you must get this from your TA on your lab notebook.
  28. 53. To make _____ measurements on a DMM you must switch the probe connections to red and the fused white port.
  29. 54. Discovered that moving a magnet through a coil of wire produces electricity.
Down
  1. 1. Day of the week in which most lab reports will always be due before midnight.
  2. 3. What does the word IC in semiconductors stand for?
  3. 4. This instrument on the ADK allows you to send SPI signals to IC's.
  4. 7. If you exceed the limit on this component on your multimeter you will have to replace it.
  5. 9. This channel on the ADK allows you to make instant math calculations on a wave.
  6. 11. One of the last names of the person submitting this assignment. (So no one can copy)
  7. 12. A BJT circuit can be analyzed using this theoretical circuit when small ac signals are being used.
  8. 14. This instrument on the ADK allows you to analyze transfer functions.
  9. 15. Portion of the lab report that states the relevant theoretical information.
  10. 16. This amplifier setup has the input signal applied to base and the output is taken at the emitter.
  11. 17. This is unethical and will cause you to get a zero on your assignment.
  12. 19. If your probe is not _________ your measurements might be inaccurate.
  13. 20. Digital to Analog converter
  14. 24. These are the people you go to when you are falling behind.
  15. 26. This software is used to graph all data acquired from a lab session.
  16. 28. The software that controls all of the instruments provided by the Analog Discovery.
  17. 35. This policy states that you will lose two points after the due date has passed.
  18. 38. A communication protocol that allows you to control some instruments through software programs.
  19. 39. Portion of the lab report that gives a quick overview.
  20. 45. Lab _______ will be the way that TA's will gauge your lab performance.
  21. 46. When analyzing square waves coming from a digital circuit you must set the appropriate high voltage threshold using this setting on the oscope.
  22. 47. Universal Serial Bus
  23. 49. Measurement commands that are sent to GPIB available instruments.
  24. 50. All screenshots from the ADK must contain this number in order to verify it is your device and your work.
  25. 51. The product of voltage and current.