Across
- 3. Write down the date and ______ for oscilloscope screenshots.
- 4. This button will open the waveform generator instrument in ADK.
- 5. If a person is suffering from electric shock, turn ______ electrical power source.
- 7. Prevent connecting the input connector to the ______ connector.
- 10. Plagiarized material will be graded as this number.
- 12. The text next to the cursor if you hover it above a tool button in Multisim.
- 14. Make sure your solder is ______ free .
- 15. The number of times you are graded for lab proficiency.
- 17. The group in the Multisim components tools bar that allows you to place resistors.
- 19. The view in ADK that allows you to access signal type, frequency and phase.
- 24. Submissions on blackboard shall not use this type of block.
- 27. MATLAB uses this variable to store the results of a calculation.
- 29. Read the lab ______ before the start of your lab .
- 31. The panel where you can build an output signal in ADK.
- 33. Your report's point size should be between 10 and ______ .
- 34. Recordings of classroom lectures is considered this type of property.
- 35. Analog and Oscilloscope screenshots need your ______ number included.
- 38. The number of isolated output channels the Keithley power supply offers.
- 39. Use this application when designing a graph for your report .
- 40. Use load ______ heavy enough so that they won't be overheated.
- 41. The number of points deducted per missing lab or lecture session.
- 42. This button on the power supply will set the voltage output.
- 43. In Analog Discovery 2's o-scope, this button will begin capturing data.
- 45. The number of times your notebook will be graded a semester.
- 46. In case of an emergency, call the university ______.
- 49. Lab reports are worth this percent of your grade.
- 50. Refrain from eating in the lab to avoid ingesting.
- 53. Use this application when designing a table for your report.
Down
- 1. Before powering an o-scope, ground it and ______ .
- 2. The % symbol in MATLAB will ______ your code.
- 6. The function generator has three generators in one and a ______ counter.
- 8. Include ______ of your completed breadboard and setup .
- 9. Observe all terminal ______ to prevent fire or shock hazards.
- 11. The panel used to explore data that you create or import files from in MATLAB.
- 13. Keep fingers behind the finger guards on the o-scope ______.
- 16. The oscilloscope allows you to store data externally through this device.
- 18. If the power supply doesn't turn on, the first step is to check ______ cord.
- 20. To place a pin array in Multisim, first select this tab.
- 21. The type of panel buttons on the o-scope to set up analog channels.
- 22. Don't forget to perform all ______ in your notebook beforehand .
- 23. From this tab, begin entering values for BJTs in Multisim.
- 25. The time by which items are due on blackboard .
- 26. What you absolutely cannot record your notebook with.
- 28. The tab in Multisim where errors from SPICE netlist checks appear.
- 30. This function creates 2D line plots in MATLAB.
- 31. This command in the power supply clears the event registers and error queues.
- 32. A list of commands that will be executed by MATLAB.
- 36. Number of prongs your power cords must need.
- 37. The application allows you to access Analog Discovery devices.
- 43. A grading tool that will be used when grading a lab report.
- 44. These buttons on the function generator are labeled as item number one.
- 47. This should be drawn through your mistake in your notebook.
- 48. Submit your pre-lab to ______ before your lab period.
- 51. Next to your mistake in your notebook this will be added.
- 52. Don't use this to extinguish an electrical fire .